manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 166

6 - 30   ELECTRICAL SYSTEM   

FIGURE 33

    If an adjustment of tone is desired, proceed as follows:
1. Remove cover (J) by inserting a screw driver in opening 

provided at edge of cover.

2. With car engine running at proper RPM to deliver the 

maximum charging rate, loosen the lock nut and turn the 

adjusting nut (H) up or down until the desired tone is 
obtained.

NOTE: It is advisable to have only one horn connected 
when the following adjustment is being made. Remove 
the wire at the horn relay from the horn not being adjust-
ed. Proceed in this manner with each horn, and after each 
horn  has been tested, connect both to relay and sound 
together, then replace cover "J", Figure 33.

3. After adjustment is made, be sure to tighten lock nut 

against the adjusting nut. (H).

    The air gap between field "A" and the armature "B" 

should be .027" to .029" on the high horn, 032" to .034" on 

the low horn.

    The armature (B) is threaded on to diaphragm stud (C) 
which is attached to diaphragm (D). Armature (B) is locked 

in the desired position by lock nut (E). Therefore, to set air 
gap between field (A) and armature (B) loosen lock nut (E) 

and turn armature (B) in a clockwise direction to decrease 

air gap

 

and counter-clockwise to increase air gap. Tighten lock nut 
(E) securely before checking gap. The armature (B) should 

be approximately parellel with the field (A).
    After the air gap has been properly adjusted, it is necessary 

to readjust nut (H) to obtain maximum volume and the best 

tone.
    If for any reason the front housing and air column 

assembly has been removed, care should be taken when 
replacing it to see that the gasket between the diaphragm, 

front housing, and air column assembly is in good condition.

    A new gasket is recommended as any air leak in the air 
column reduces the volume and quality of tone.

    The short air column is used in conjunction with the thick 
diaphragm for the high horn. The long air column is used in 

conjunction with the thin diaphragm for the low horn.

DIRECTION INDICATOR SWITCH

ELECTRICAL CHECK:

1. Disconnect switch wires from connectors under instru-

ment panel.

2. Connect black wire to hot side of circuit breaker.

3. Connect one lead of test lamp to blue switch wire and 

ground the other lamp lead. Move switch lever down and 

lamp should light.

4. Connect one lead of test lamp to yellow switch wire and 

ground the other lamp lead. Move switch lever up and 

lamp should light.

5. If lamp fails to light in either position, switch should be 

replaced.

MECHANICAL CHECK:

NOTE: For proper operation of direction indicator, steer-
ing wheel must be properly Installed in straight ahead 
position on steering column

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды