manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 310

15 - 4  BRAKES   

5. Remove master cylinder.

REPAIR:

1. Thoroughly clean exterior of cylinder before disas-

sembling.

2. Remove filler plug (1) Figure 2 and drain fluid.

3. Remove push rod guard strap (7) at push rod and remove 

push rod (6) and guard (8).

NOTE: Do not use gasoline, kerosene, or carbon tetra-
chloride for cleaning solution. Use clean alcohol. Keep 
the parts free from mineral oil of any kind.

4. Remove lock wire (9). This will allow removal of piston 

(13), piston cups (11) and (15), spring (17), and check 

valve (18) for inspection and replacement, if necessary.

ASSEMBLING:

1. Wash master cylinder parts in clean alcohol.

2. After washing, dip all parts in "Hudson Hydraulic Brake 

Fluid" for lubrication.

3. Install check valve (18) and piston return spring (17).

4. Install primary cup (15) piston assembly (13) and piston 

stop plate (10).

NOTE: Always use new rubber cups.

5. Snap piston stop plate lock wire (9) in its groove.

6. Assemble push rod guard (boot) (8) and push rod (6) in 

place and install strap (7).

INSTALLATION:

1. Install master cylinder bracket and insert the two 3-1/2" 

long bolts (13) Figure 1 through bracket and master cylin-

der housing and tighten securely.

2. Attach the two brake tubes to master cylinder connector 

(15) and stop light switch wires to stop light switch (16).

3. Install master cylinder push rod assembly (12) to brake  

pedal lever (8) and insert clevis pin (10) and cotter pin. 
(Turn ends of cotter pin).

4. Insert the bolt attaching the master cylinder bracket to 

frame (located between master cylinder and frame).

5. Attach clutch pull back spring t o master cylinder bracket.

6. Refill master cylinder to required level with Filler Bottle 

J-713 using "Hudson Hydraulic Brake Fluid".

NOTE: After  removing master cylinder of any brake hose 
connections, it is always necessary to bleed the hydraulic 
brake lines to expel any air that may have entered the 
system. See "Bleeding Brakes" Page 7.

FIGURE 4

1. Wheel cylinder

2. Wheel Cylinder end guard
3. Piston

4. Piston cup
5. Piston cup spring

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды