manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 177

FIGURE 7

    If any finger is more than .030" higher than another, it 

should be lowered to level of other finger's by Installing a 
thin (about .005" thick) washer between clutch cover and 

retainer of the high finger.

11. Remove assembly from fixture.

Installation OF CLUTCH

ASSEMBLY TO ENGINE

1. Install ONE new clutch cover gasket and shellac it in 

place on front face of cover flange.

NOTE: If clutch has been properly reconditioned only one gas-
ket of 1/32" free thickness is required to give correct release and 
engagement. Avoid the Installation of two or more gaskets as 
each added gasket reduces the effective pressure of engaging 
springs by an amount equal to the thickness of each additional 
gasket.

2. Place driving plate on pressure plate then insert the aligning arbor 

J-449, through cover and splines of driving plate and into pilot 

bearing in flywheel. Push the assembly up into place on the 

flywheel and secure with the cap screws. Keep the arbor in 
position so as to keep the driving plate centered. This will assist 

Installation of the transmission.

3. Tighten the cap screws gradually drawing down oppo-

site screws instead of in rotation so that a good gasket 

seal is insured. Using; a torque wrench, tighten all 

cover screws to 20-25 foot pounds. Withdraw the arbor.

4. Insert 1/3 of a pintof Hudsonite into clutch via the 

cover hub opening.

5. Install clutch collar and throwout b axing assembly to 

clutch cover hub bore after spreading a thin coat of 

engine oil over bore wall. Care must be exercised to 
prevent damaging the lip of the oil seal or curling it 

over in the bore.

6. Center the throwout bearing grease retainer leather 

washer (17), Figure 1, (not the oil seal) by temporarily 

inserting the aligning arbor through it. Rotate collar 
and throwout bearing to position for proper alignment 

with throwout yoke on transmission.

7. Tighten  al 1 rear engine support plate screws.
8. Install two headless screws J-2969 in engine endplate 

to assist in supporting transmission at Installation.

9. Bring the transmission assembly to position where 

main drive gear (clutch shaft) is aligned with bore of 

throwout collar, then carefully push forward to enter 
drive gear through grease retainer leather washer, 

splines of driving plate and into pilot bearing. During 
this operation the main drive gear must be relieved of 

the overhanging weight of the transmission until the 

bell housing engages the dowels.

NOTE: Before transmission assembly is moved up 
against rear support plate, make a last inspection to 
verify that the end face of throwout collar in clutch is 
properly aligned with throwout yoke on transmission 
and that oil seal lip has not turned under.

CAUTION: Alignment of bell housing with engine is 
controlled by the sleeve dowel in the upper left location 
of the bell housing attaching bolt circle and by the 
dowel bolt at the lower right location viewed from rear 
of car. Make sure that the former is in place and entered 
in bell housing hole before tightening bolts. Install 
Lower right bolt (dowel bolt) first. NEVER grind or 
otherwise reduce the diameter of the dowel bolt to 
facilitate Installation.

CLUTCH   7 - 9

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды