manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 248

11 - 6   REAR AXLE

2. Remove hub and drum by means of hub puller J-736 as 

shown in Figure 8. (Do not strike the end of the axle shaft 

to loosen the hub because of possible damage to the 
bearing and the center drive shaft thrust spacer).

FIGURE 8

3. Remove nuts and lockwashers which hold the rear wheel 

bearing adjusting cap and oil seal assembly to the back-
ing plate and axle housing.

4. Remove adjusting cap and oil seal assembly and shims.

NOTE: It is important if shims are to be removed from 
both sides of the axle, that each set should be kept sepa-
rate, and reassembled in their original location, in order 
that proper bearing adjustment is maintained. If an axle 
shaft, bearing, carrier or housing is to be replaced by 
another part, the axle shaft and play should be checked 
and corrected.

5. Remove axle shaft and wheel bearing, using  axle shaft 

puller J-352. See Figure 9. 

FIGURE 9

6. Remove bearing from axle shaft, using bearing remover 

J-358 - H - 1 Holder and J-2641 Adapter, Figure 10.

FIGURE 10

7. Remove axle shaft inner oil seal, using tool J-943. See 

Figure 11.

NOTE : It is advisable to replace old oil seals with new 

seals in order to prevent leakage.

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды