manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 11

LUBRICATION   1 - 1

SECTION 

1

LUBRICATION

 The present day high speed driving, fast acceleration, 

and precision fitted engine parts have placed engine and 
chassis lubrication in the category of highly specialized 

services.

 A definite plan of application is necessary to provide 
the various working surfaces with the right amount of the 

correct lubricant at the proper time.

 Contrary to general belief, one type of lubricant will not 

suffice to all applications.

 Varying load demands and operating conditions call for 

different types of lubricants.

 Authorized Hudson Dealers have been provided with a 

Lubrication Chart covering correct factory lubrication 

speci

specifications, and a definite plan of application. Observance 

of this chart and its requirements will be definite assurance 
of customer satisfaction and goodwill.

 A copy of the Lubrication Chart is also included in this 
manual. Additional helpful information regarding the lubri-

cation requirements are given in the Lubrication Schedules 

and the following paragraphs.

NOTE: The lubricants used at the time of assembly are of 
the best quality and need not be changed until the recom-
mended change period shown in the Lubrication Schedule.

LUBRICATION SCHEDULES

500 Miles

 Drain the original engine oil at 500 miles and refill with a good grade of oil of the viscosity rating shown in the 

temperature and viscosity illustration, Figure 3, Page 6. For engine oil capacities of six and eight cylinder engines refer to 
Figure 1 - -Lubrication Chart and Capacities-- Page 10.

1,000 Miles

Viscous Chassis Lubricant

Points

Drag Link         

2

Upper Support Arm Eccentric Bushing.     

2

Upper Support Arm Pivot Bushing     

4

Lower Support Arm Pivot Bushing.       

4

Lower Support Arm Support Bushing      

2

Center Steering Arm Pivot Bearing      

1

Tie Rod End          

4

    Points

Steering Spindle Pivot Pins          

2

Gear Shift Bell Crank Pivot          

1

Clutch Pedal Bearing          

1

Clutch Throwout Bearing         

1

Universal Joint Spline         

1

Rear Spring Shackle Bushing          

4

Engine Oil

    Points

Engine       Check Oil Level    
Door Hinge           4 or 8

Gasoline Tank Filler Door Hinge    
   and Spring        

3

    Points

Rear Compartment Door Striker        

4

Rear Compartment Latch Rod         

2

Hood Hinge          

8

Windshield Wiper Pulleys          

4

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды