manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 132

5 - 6   COOLING SYSTEM

clearance for the pulley hub. The slotted adaptor is placed 
between the body and the pulley hub to support the lower 
part of the body to eliminate spring-back and possible 
body fracture when removing the water pump shaft

.

    The bearing and shaft is serviced as an assembly only. 

The water pump pulley hub (19) is not part of the shaft and 
must be removed from the old shaft and Installed on the 

new shaft. The adaptor included in J-2778 Holding Fixture 
Kit can be used to remove the pulley hub.

NOTE: Check the water pump body bore for scores and 
wear. Inspect seal surface in pump body, if rough, reface. 
If scored, replace pump body.

    Also check the pump body at the area of the impeller 
and if the impeller has been scraping the body, it indi-

cates the excessive end thrust and complete pump 
should be replaced.

WATER PUMP SHAFT AND

BEARING INSPECTION

1. Revolve bearing slowly by hand, using hand thrust 

load. If bearing does not drag or feel rough, it can be 

reused.

2. If steel seals at ends of bearing, outer races are loose so 

that they can be turned with the fingers, the bearing 

should be replaced.

3. Worn shafts and shafts with a worn spring retainer 

groove should be replaced.

REASSEMBLY: - 6 Cylinder

1. Assemble the shaft and bearing in the water pump 

body.

NOTE: Bearing should be slight press fit into pump 
body, and assembled so that the groove on the outer 
race is aligned with the retainer wire slot in pump 
body bore.

CAUTION: When pressing bearing and shaft in housing, 
press against face of outer ring, not against shaft.

2. Lubricate shaft with castor oil and Install the fan pulley 

hub '(19). Support the flange of the hub and apply pressure 
on the impeller en d of the shaft. Maintain proper pulley 

spacing. This dimension should be 5-5/32" from outside 

edge of hub to cover face of pump body, shown as "A", 
Figure 2.

NOTE: Pump body should be allowed to float during this 
operation.

FIGURE 4

3. Lubricate shaft with caster oil to facilitate assembly and 

assemble the seal (13) and carbon washer (14) and re-

tainer (8) in the impeller and Install impeller by support-
ing the assembly on the fan end of the shaft as shown in 

Figure 4.

NOTE: Impeller must protrude .007 to .017 beyond cover 
face of pump body, Figure 2.

4. Install the water pump shaft and bearing retainer (6), 

Figures 2 & 3.

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды