manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 58 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 58

1126800 

SmartPAC 2 with WPC Integration

Page 36

Chapter 2

Installing SmartPAC 2 and WPC

local codes require it) is recommended for these circuits with a minimum 75°C temperature
rating.  To perform the wiring, follow these steps.

1. Locate the power supply board (situated under the main processor board).  You will see

the connector for AC power.

2. Determine how you will bring wiring from your 115 VAC power source (or 230V source

if applicable) to the unit.  For 115 VAC, you need three wires—high (black), neutral
(white) and ground (green).  For 230 VAC, wires are black and red with green or
green/yellow for ground.

3. Find the 115V-230V voltage selector switch. It can be found on the side of the power

supply board (see Figure 2 - 37, page 160).

•

  If your AC power is 115V, check to see that “115V” is displayed in the switch cavity.

•

If your AC power is 230V, push the handle to the right.

Push handle
to the left for

115V

(to the right for

230V)

115V

Figure 2 - 6.  Setting Voltage Selector Switch

4. Run the power wires to WPC through flexible liquid-tight conduit to the enclosure.

Because WPC is rated NEMA 12 (protected against dust and oil), you must use conduit
of the same rating and make proper connections to ensure NEMA 12 protection with the
enclosure.

5. To make ground connections, refer to the diagrams at the end of the manual and to the

WPC connections wiring, Table A at the end of the manual.

6. Connect  power wires.  For 115 VAC power, connect the black wire to HI terminal and

white wire to NEU. (For 230 VAC connect black wire to HI terminal and red wire to
NEU). Attach wires to the terminal block connector as instructed on page 30.  Make sure
that you do not start at the wrong end of the connector. Put it over the socket the way it
will plug in, and note wire markings next to the socket before starting.

7. Plug connector back into its slot. Double check connections with markings at the

connector base to make sure you did not wire it backwards.

8. Make all necessary conduit connections to ensure NEMA 12 protection “NEMA 12

protection” .  WPC is rated NEMA 12 (protected against dust and oil).  

Be sure to label

all wires in a way consistent with your press’s electrical prints.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов