manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 152 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 152

1126800 

SmartPAC 2 with WPC Integration

Page 130

Chapter 2

Installing SmartPAC 2 and WPC

Check Safeguarding Devices

DANGER

!

INJURY DURING TESTING

Keep all personnel away from the press during testing.

Ensure that there is no die or other tooling in the press during testing.

•

Use extreme caution when testing moveable guards.  Keep hands and other body parts
outside the guarded area.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

NON-SAFETY INTERLOCK SWITCHES USED IN SAFETY APPLICATIONS

Ensure that all interlock switches used on safeguards are designed and rated for safety
applications.  Check with the manufacturer to verify each interlock switch’s rating.

Ensure that safety interlock switches are connected to control-reliable inputs if they are used
for safeguarding applications.

Failure to comply with these instructions will result in death or serious injury.

Before turning on the press, verify the following:

•

All fixed safeguards prevent entry of a hand or other body part into the hazardous
area.

•

All moveable safeguards are correctly installed and wired to prevent operation of the
press when they are open and prevent entry of a hand or other body part into the
hazardous area.

•

All interlock switches used with safeguards are designed and rated for use in safety
applications. Check with the switch manufacturer to confirm their suitability for
safety use.

•

Interlock switches used for safeguarding are connected to control reliable inputs.

•

Any light curtains are installed correctly and working properly.

•

Any two-hand controls used as safeguarding devices are mounted at least the safety
distance from the hazardous area.

•

Safeguards are in place to prevent entry to the hazardous area under, over or around
light curtains or other safeguarding devices.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов