manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 100 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 100

1126800 

SmartPAC 2 with WPC Integration

Page 78

Chapter 2

Installing SmartPAC 2 and WPC

S101

Push switch down

 for 12-60V

Push switch up

 for 60-250V

Figure 2 - 21.  Input check switch (S101)

NOTICE

HOW THE INPUT CHECK CIRCUIT DETECTS RESOLVER CHAIN BREAKAGE

When the dual safety valve relay is energized by the press control to start the press, voltage
will be produced in the input check circuit. This signals SmartPAC 2 that the press ram
should begin to move. If SmartPAC 2 gets no signals from the resolver within the start time
limit (resolver not turning), it opens the emergency stop circuit.  A  “loss of rotation” fault
message is displayed on the screen. The press could have started but the resolver belt or
chain broke or was significantly too loose so that the resolver shaft did not move. Other
possible reasons for the fault could be low air pressure to the clutch or a bad clutch.

2.

 

Run the stop circuit, and input check circuit wires to SmartPAC 2 through flexible
liquid-tight conduit to the enclosure.  Because SmartPAC 2 is rated NEMA 12 (protected
against dust and oil), you must use conduit of the same rating and make proper
connections to ensure NEMA 12 protection with the enclosure.

3.

 

Locate connector TB102 for the stop circuits. It should be plugged into the socket.
Connect the wires for the stop circuits and input check SmartPAC 2 as shown in the table
below. (Also refer to Figure 1 at the end of the manual.)

Table 2 - 4.  Wiring to Input Check and Stop Circuits

SmartPAC 2

TB102

Terminal

Wiring

Designation

WPC Control

Board

Pin #

205

A

41

206

B

29

207

E-Stop

68

208

E-Stop

67

209

Top Stop

80

210

Top Stop

79

9. Plug the connector back into its slot.  Double check connections with markings at the

connector base to make sure that you did not wire it backwards.

10. Connect top stop, E-stop, and check input circuit wires at the press control.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов