manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 20 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 20

1126800 

SmartPAC 2 with WPC Integration

page xvi

Table of Contents

How to use the manual

This is the installation and reference manual for SmartPAC. It has information about how to
install SmartPAC and use all the displays to make die protection sensor settings and
programmable cam settings.

Chapter 1 introduces you to SmartPAC, tells how it works — specifically about the optional
die protection (DiProPAC) and programmable cam (ProCamPAC) features, and explains
how to use this product.

Chapter 2 is the installation chapter. Use it to install SmartPAC if you are installing it
yourself.  This chapter includes installation of the DiProPAC and ProCamPAC options.

Chapter 3 is an introduction to the SmartPAC displays and keyboard. Read this chapter to get
started using SmartPAC. It shows you how to select items on the SmartPAC displays and
how to perform key tasks. It also explains the various keys available. This chapter is the
place to start for learning how to use the SmartPAC displays and keyboard.

Chapter 4 explains how to use SmartPAC in Initialization mode. Use it to look up things you
need to know about using SmartPAC in Initialization mode.

Chapter 5 explains how to use SmartPAC in Program mode. Use it to look up things you
need to know about Program mode.

Chapters 6 explains how to use SmartPAC in Run mode. You can look up things you need to
know about Run mode.

Chapter 7 shows you fault messages or other types of messages you will see on your display
when SmartPAC sends a stop command to the press or when there is an equipment or
software problem. What the message means and how to correct the problem is explained. Use
this chapter to learn about all the SmartPAC diagnostic messages.

Appendix A gives excerpts from OSHA and ANSI standards.

Appendix B is about the optional PM (Preventative Maintenance) Monitor available with
SmartPAC.  It explains what it is, how it works, and application examples.  It also provides
instructions on using it in Initialization and Run modes (not used in Program mode).

Appendix C gives instructions for updating SmartPAC 2 program.

Appendix D gives instructions for using SmartView remote viewing utility.

Appendix E gives instructions for upgrading from an original SmartPAC to a SmartPAC 2.

Appendix F gives instructions for replacing the SmartPAC 2 PC board.

A Glossary of Terms gives definitions of key terms related to SmartPAC.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов