Honeywell SmartPAC 2 Скачать руководство пользователя страница 464

Страница: 464 / 522

1126800

SmartPAC 2 with WPC Integration

page 442

Appendix B

SmartPAC Preventive Maintenance

(PM) Monitor

RESOLVER ZERO
POSITION SENSOR
PRESS NAME
SELECT CAM NAMES
AUTO ADVANCE
CUSTOM SENSOR NAMES
SENSOR ENABLE MODE

SECURITY ACCESS

MAIN INITIALIZATION MENU

USE CURSOR KEYS TO
CHOOSE MENU ITEMS.
PRESS THE ENTER
KEY TO SELECT.
SWITCH TO RUN WHEN
DONE.

PM MONITOR

Figure B - 2. "PM Monitor" Highlighted at SmartPAC Initialization Menu

2. Select "PM Monitor" from the main Initialization menu (Figure A-1). A screen will

appear asking for your password.

NOTICE

The password prompt will appear EVERY time that you select "PM Monitor" from the
Initialization mode.

ENTER THE PASSWORD

USE THE KEYPAD TO ENTER NUMBERS.
USE THE UP/DOWN CURSOR KEYS TO
INCREMENT/DECREMENT. PRESS ENTER
WHEN DONE. PRESS RESET TO CANCEL.

65535

Figure B - 3. PM Password Screen

3. At this point, consider the applicable alternatives below, depending on whether you have

new system

(which includes the PM option already installed at the factory), or an

existing

SmartPAC (where you have to install and initialize this option yourself).

Proceed with the one that corresponds with your system.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Результаты поиска

Содержание SmartPAC 2

Отзывы:

Honeywell SmartPAC 2, Руководство пользователя, Страница: 464 / 522

Результаты поиска

Содержание SmartPAC 2

Отзывы: