Honeywell SmartPAC 2 Скачать руководство пользователя страница 413 | Manualshive

Страница: 413 / 522

Honeywell SmartPAC 2 Скачать руководство пользователя страница 413

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Fault Messages

Chapter 7

page 391

number

(e.g. Vs. 2.00). You can determine the last two items, by going into "Installed

options" in the Initialization mode (see Chapter 4 for details). Here is a description of the
types of codes.

F SERIES STATUS CODES

Any codes preceded by the letter "F" are generated by WPC’s first internal processor and
are operator-resettable. This means that after you correct the malfunction, you can press
SmartPAC RESET key or the EMERGENCY STOP / RESET button on the operator station
(or remote reset switch, if installed). and resume operation. If the problem is corrected, you
will be able to run the press again. If not, you will get the same fault message again.

H SERIES STATUS CODES

Some "F" errors codes are followed by "H" status codes. Like "F" errors, these "H" codes
are operator-resettable. "H" status codes are generated by the second internal processor.
With its two independent processor systems in a single modular enclosure, WPC provides
dual diverse redundancy — the latest technology in maintaining optimum clutch/brake
control and operator safety. Both of these processor systems function independently of
each other and provide separate information to the operator. Therefore, error conditions will
be detected from either or both of the two processors resident in the system. As with "F"
series status codes, after you correct the malfunction, you can press SmartPAC's RESET
key or the EMERGENCY STOP / RESET button on the operator station (or remote reset
switch, if installed). and resume operation.

Messages Displayed Due to Press Control Problems

These messages tell you that something is wrong with the configuration of SmartPAC 2 with
WPC, or with the way your press is running. Some fault messages indicate that there is a
problem specifically related to the brake monitor and/or press control. These messages may
also indicate an internal problem with SmartPAC itself.
If you cannot correct the problem after reading the remedy, contact Wintriss Tech Support.
Whenever you need help, just remember that we have expert representatives available to help
you by phone. Be sure to provide pertinent information to expedite the resolution to your
problem.
After you have corrected the problem, press RESET. If the problem is corrected, you will be
able to run the press again. If not, you will get the same fault message.

«
...
411
412
413
414
415
...
»

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов