Honeywell SmartPAC 2 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 522

Honeywell SmartPAC 2 Скачать руководство пользователя страница 45

Installing SmartPAC 2 and WPC

Chapter 2

page 23

SmartPAC 2 with WPC Integration

1126800

Chapter 2 – Installing WPC and
SmartPAC 2

DANGER

!

IMPROPER INSTALLATION, USE OR MAINTENANCE

•

Follow all procedures in this manual, including checkout procedures and tests. Perform only
the tests and repairs listed in this manual. Use only factory-supplied replacement parts.

•

Ensure that WPC clutch/brake control is installed, tested and repaired by qualified
personnel.

•

Wire, install and maintain WPC clutch/brake control in accordance with the applicable safety
standards. Carry out all inspection procedures in OSHA 1910.217

•

Wire and install all equipment in accordance with the requirements of OSHA 1910.147
Control of Hazardous Energy (Lockout/ Tagout).

•

Install and maintain your machine guarding system according to OSHA standard 1910.217,
ANSI B11.1, ANSI B11.19 and any other regulations and standards that apply. Ensure that
guarding is properly installed to prevent access to the machine over, under or around any
guarding device.

•

Perform the checkout procedure after installation and after any modification or repair of the
WPC clutch/brake control.

•

Lockout/Tagout the press during all installation, modification, repair or maintenance
procedures.

•

Ensure that supervisors, die-setters, maintenance persons, machine operators, foremen,

and any others responsible for operation of the machinery have read and understood all
instructions for use of the WPC clutch/brake control.

•

Disconnect the “continuous mode” position of your stroke select switch and cover the

“CONT” label on your control if the press is not properly guarded for use in continuous mode.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

FAULTY INSTALLATION

Ensure that wiring is correct.

Use only safety-certified components for safety functions, including interlock switches used
in safety applications.

Install guarding to prevent access to hazardous areas. Prevent access to hazardous areas
over, under or around any guarding devices.

Ensure that there is one active operator station for each operator if you are using two-hand
mode.

Failure to comply with these instructions will result in death or serious injury.

«
...
43
44
45
46
47
...
»

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов