manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 452 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 452

1126800 

SmartPAC 2 with WPC Integration

page 430                          Appendix A               Excerpts from OSHA Regulations and ANSI Standards

Excerpts from OSHA Regulation 1910.217

OSHA Regulations

PMA Interpretation

Ds = minimum safety distance (inches);

63 inches/second = hand speed constant;

and

Ts = stopping time of the press measured at

approximately  90

°

 position of crankshaft

rotation (seconds).

Example:

Measured stopping Time = 0.190 seconds

Time Factor = 1.2 x 0.19 = 0.228 seconds

Calculation = 63 x 0.228

Safety Distance = 14.4 inches

OSHA 1910.217 (e) (1)

(e) INSPECTION, MAINTENANCE, AND
MODIFICATION OF PRESSES

(i) It shall be the responsibility of the
employer to establish and follow a program
of periodic and regular inspections of his
power presses to insure that all their parts,
auxiliary equipment, and safeguards are in
safe operating condition and adjustment. The
employer shall maintain records of these
inspections and the maintenance work
performed.

Records of clutch and brake will be weekly. Other
inspections are periodic subject to time factor
determined by employer.

(ii) Each press shall be inspected and tested
no less than weekly to determine the
condition of the clutch/brake mechanism,
anti-repeat feature and single stroke
mechanism. Necessary maintenance or repair
or both shall be performed and completed
before the press is operated. The employer
shall maintain records of these inspections
and the maintenance work performed. These
requirements do not apply to those presses
which comply with paragraphs (b) (13) and
(14) of this section.

If brake monitoring system is installed, weekly
inspection and records are not required for
clutch/brake mechanism. Other parts of the press will
require periodic inspections and records.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов