manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 242 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 242

1126800 

SmartPAC 2 with WPC Integration

Page 220

Chapter 4

SmartPAC 2 Initialization Mode

Enabling or Disabling Setup Mode

(INITIALIZATION - SENSOR ENABLE MODE)

NOTICE

If your SmartPAC 2 is 

not 

integrated with a WPC, your inch-selector switch must be wired to

the setup mode input, terminal #252 on TB107.

If you enable Setup mode, the green sensors are disabled in the condition you choose:

•

In Inch mode
or

•

In Inch mode 

and 

 in Interrupted-stroke mode. (Available only with WPC integration)

For more information, see the Initialization chapter in your user manual.

1. To enable or disable Setup mode, in the Main Initialization menu, select SENSOR

ENABLE MODE.

MAIN INITIALIZATION MENU

USE THE CURSOR 

  RESOLVER ZERO

KEYS TO CHOOSE

  POSITION SENSOR

MENU ITEMS. PRESS   INSTALLED OPTIONS
THE ENTER KEY TO

  SELECT CAM NAMES

SELECT. SWITCH TO    AUTO ADVANCE
RUN WHEN DONE.

  CUSTOM SENSOR NAMES
  SENSOR ENABLE MODE
  PROCESS MONITOR
  TOOL INFORMATION
  RAMPAC INIT
  PRESS CONTROL
  SECURITY ACCESS

SENSOR ENABLE MODE

Figure 4 - 15.  Main Initialization Menu

A screen similar to the following appears.

DIE PROTECTION MODE SELECTION MENU

SENSOR ENABLE MODE =    AUTO BY TOOL
SETUP MODE                    =    DISABLED

USE THE CURSOR KEYS TO SELECT THE MODE
YOU WANT TO CHANGE. PRESS THE ENTER KEY
TO CHANGE IT.  PRESS THE RESET KEY WHEN
YOU ARE DONE.

DISABLED

Figure 4 - 16.  Setup Mode Status

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов