Honeywell SmartPAC 2 Скачать руководство пользователя страница 117

Страница: 117 / 522

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 95

Part 6 – Set Up SmartPAC2 with WPC

DANGER

INJURY DURING SETUP OR TESTING

Keep all personnel away from the press during setup and testing.

Ensure that there is no die or other tooling in the press during setup and testing.

Failure to comply with these instructions will result in death or serious injury.

CAUTION

DAMAGE TO PRESS AND/OR DIE

Ensure that no die is mounted in the press during test and setup procedures.

Failure to comply with these instructions could result in property damage.

Turn On Power to SmartPAC 2 and WPC, next page

Problems at Startup, page 98

Verify Proper Installation of ProCamPAC and/or DiProPAC Options, page 100

Initialize WPC Press Parameters, page 101

Create and Load a Test Tool Number, page 103

Check and Set Direction of Resolver Rotation, page 104

Zero the Resolver, page 105

Set Top Stop Angle and Install Overrun Magnet, page 107

Prepare to Install Magnet for Overrun Limit Sensor, page 116

Install Magnet for Overrun Sensor, page 125

Check the ON and OFF Time of the Overrun Sensor, page 126

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Результаты поиска

Содержание SmartPAC 2

Отзывы:

Honeywell SmartPAC 2, Руководство пользователя, Страница: 117 / 522

Результаты поиска

Содержание SmartPAC 2

Отзывы: