Honeywell SmartPAC 2 Скачать руководство пользователя страница 53

Страница: 53 / 522

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 31

insert wire here

tighten screw to clamp
wire in terminal

Figure 2 - 2. Attaching Wires to Connector

How to Terminate Cable Shields

NOTICE

TERMINATE BOTH ENDS OF SHIELD

Be sure to terminate the cable shields at

both

ends (for example, at SmartPAC 2

and

DSI 2).

Your Wintriss units have ground studs on the inside of the enclosure for terminating cable
shields at the point of entry.

Secure drain wire
under nut on
ground stud

Drain wire

Strip cable jacket
as far as end of
conduit fitting

Figure 2 - 3. Connecting Shield Drain Wire to Ground Stud

For each shielded cable, perform the following steps. Refer to the figure above.

1. Strip the cable jacket as far as the end of the conduit fitting.

2. Cut the drain wire to a length that can wrap at least once around the nearest ground stud.

Loosen the nut on the stud, wrap the drain wire around clockwise and tighten the nut.

3. Connect the rest of the wires in the cable to the terminal block as appropriate.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Результаты поиска

Содержание SmartPAC 2

Отзывы:

Honeywell SmartPAC 2, Руководство пользователя, Страница: 53 / 522

Результаты поиска

Содержание SmartPAC 2

Отзывы: