manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 385 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 385

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Run Mode

Chapter 6

page 363

Figure 6 - 31.  Sample E-mail to Wintriss Tech Support

TOGGLE HOT KEYS

(RUN – TOGGLE HOT KEYS)

Select this item to switch between the two sets of Hot keys.  See the following figure.

For more information about programming and using Hot keys, see page 323.

F1

F2

F3

F4

F5

F6

F7

F8

    

F1

F2

F3

F4

F5

F6

F7

F8

Figure 6 - 32.  Toggle Hot Keys 1 and 2

For HELP press the HELP key located at the center of the cursor (arrow) keys.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов