Honeywell SmartPAC 2 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 522

Honeywell SmartPAC 2 Скачать руководство пользователя страница 110

1126800

SmartPAC 2 with WPC Integration

Page 88

Chapter 2

Installing SmartPAC 2 and WPC

Table 2 - 7. Making Connections to Relays

Module

How to connect

Type

Relay

one wire to C; one wire to N/O or N/C; polarity does not matter

SPDT

DC Solid State

– to C; + to N/O

SPST

AC Solid State

one wire to C; one wire to N/O; polarity does not matter

SPST

N/C C N/O

CHAN 5

N/C C N/O

CHAN 6

N/C C N/O

CHAN 7

N/C C N/O

CHAN 8

TB303

N/C C N/O

CHAN 1

N/C C N/O

CHAN 2

N/C C N/O

CHAN 3

N/C C N/O

CHAN 4

TB302

Figure 2 - 24. Connector TB302 and TB303 for Wiring Relays to Equipment

WARNING

!

RELAY REMAINS ENERGIZED DUE TO INCORRECT SUPPRESSOR INSTALLATION

Ensure that suppressors are correctly installed. They must

not

be installed across the relay

contacts inside the cam outputs enclosure. If a suppressor is installed across the relay
contacts and it fails shorted, the equipment controlled by that relay will remain energized all
the time.

Failure to comply with these instructions could result in death or serious injury.

10. You must install arc suppressors across each inductive load (motors, relays, coils, etc.)

that is connected to an output relay. Suppressors are supplied with each relay. The
suppressors reduce electrical noise and will extend the life of the relays. Find the
suppressors supplied with the modules.

11. Install the suppressors across the load and as close to the load as possible. Attach

suppressors by connecting leads across existing terminals or junction points. See the
following illustration for the correct way to install them.

«
...
108
109
110
111
112
...
»

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов