Honeywell SmartPAC 2 Скачать руководство пользователя страница 138

Страница: 138 / 522

1126800

SmartPAC 2 with WPC Integration

Page 116

Chapter 2

Installing SmartPAC 2 and WPC

Prepare to Install Magnet for Overrun Limit Sensor

DANGER

INJURY DURING SETUP

Keep all personnel away from the press during setup.

Ensure that there is no die or other tooling in the press during setup.

Failure to comply with these instructions will result in death or serious injury.

NOTICE

Refer to the following instructions, as necessary:

•

Install the Overrun Limit Sensor Magnetic Switch, page 44

•

Setting Switches,” page 242

•

Switches 1 and 2 – Overrun Limit Switch Setting, page 242

•

WPC LED map, Figure B at the end of the manual

NOTICE

The Top Stop Angle, which you just set, is the point in the stroke at which the Top Stop cam
turns on. The Top Stop cam stays on for 20

. The following instructions enable you to install

the Overrun Limit Sensor magnet so the overrun sensor turns on after the Top Stop cam
turns off.

1. In Run mode, select PRESS CONTROL. In the box below, write the

Top Stop Angle

Top Stop Angle

2. Check the box next to the range below that contains the

Top Stop Angle

. Go to the page

indicated.

Top Stop Angle

240

°°°°

or less

: Go to next page.

Top Stop Angle

241

°°°°

- 270

°°°°

: Go to page 119.

Top Stop Angle

271

°°°°

- 300

°°°°

: Go to page 121.

Top Stop Angle

301

°°°°

or greater

: Go to page 123.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Результаты поиска

Содержание SmartPAC 2

Отзывы:

Honeywell SmartPAC 2, Руководство пользователя, Страница: 138 / 522

Результаты поиска

Содержание SmartPAC 2

Отзывы: