manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 274 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 274

1126800 

SmartPAC 2 with WPC Integration

Page 252

Chapter 4

SmartPAC 2 Initialization Mode

ENTER YOUR

USE THE  KEYPAD TO ENTER

USE THE UP/DOWN CURSON

INCREASE/DECREASE. PRESS

WHEN DONE. PRESS RESET TO

60599

Give this number to
Wintriss Tech Support if
you forget your password.

Note:

  Your number may be

           different.

Figure 4 - 34.  “Enter Your Password” Screen

IF YOU FORGET OR DO NOT KNOW YOUR PASSWORD(S)

Contact Wintriss Tech Support at the telephone number on the cover of this manual.  Give
the tech support person the 5-digit number from the bottom of the  “Enter your password”
display.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов