manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 331 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 331

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Program Mode

Chapter 5

page 309

4.

 

You can add more arcs by pressing 

F6

-“Add a New Arc” again.

5.

 

If you want to adjust one of the arcs, press 

F7

-“Select Arc” one or more times, until the

arc you want to adjust turns green (see next figure).  Use the cursor keys to adjust the
arc.

6.

 

Press RESET when you have set the arcs you want.

NOTICE

To delete an ON/OFF output event for this cam channel you must delete channel settings
(page 313) for this channel and make the ON/OFF settings again.

Inactive arcs

are gray

Selected (active) arc
listed here
and indicated by 
green color 
on circle diagram

Figure 5 - 34.  Selected and Inactive Arcs

Selecting a Channel and Making a Timed Output Setting

NOTICE

MAXIMUM NUMBER OF TIMED CHANNELS PER TOOL

Each tool can have up to four timed-output cam channels.

A timed output setting means that you set the crankshaft angle at which you want the channel
to turn ON and the dwell duration time in milliseconds (in other words, how long you want
the channel to stay on). This makes the channel "ON-duration" independent of press speed.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов