manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 267 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 267

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Initialization Mode

Chapter 4

page 245

Switch 5 – Prior Act Timing for Automatic Single Stroke and Continuous on
Demand

NOTICE

After you change switch settings, power down the SmartPAC 2/WPC. Power it up again to
enable the new settings. If you do not this, the previous switch settings will remain in effect.

Option Switch 5 sets the prior act timing for Automatic Single Stroke mode and for
Continuous on Demand mode.  The switch in the OPEN position selects the shorter prior act
time for both modes (30 seconds/1 minute, respectively). The switch in the CLOSED
position selects the longer prior act time for both modes (5 minutes/10 minutes, respectively).
Refer to the table below .

For more information about Automatic Single Stroke mode, see “Operating the Press in
Automatic Single Stroke Mode,” page 373. For more information about Continuous on
Demand mode, see “Operating the Press in Continuous on Demand,” page 377.

Set Switch 5 in the Press Control Option Switches screen, Figure 4 - 33, page 241.

Table 4 - 8.  Switch 5 Setting for Prior Act Timing

Option Switch 5 Setting

Prior Act Timing for

Automatic Single Stroke

Prior Act Timing for

Continuous on Demand

OPEN

30 seconds

1 minute

CLOSED

3 minutes

10 minutes

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов