manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 272 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 272

1126800 

SmartPAC 2 with WPC Integration

Page 250

Chapter 4

SmartPAC 2 Initialization Mode

Automatic Mode

Enable "Automatic Mode" when you wish to use Automatic Single Stroke or Automatic
Continuous.  This allows you to automate a press using a feeding device or robot. See
Chapter 2 for installation of Automatic Single Stroke (also known as External Trip),
Chapter 6 for using this feature.  Call Wintriss Tech Support for information about using
Continuous on Demand..
1. In the Press Control Option Switch screen, Figure 4 - 33, highlight the item next to

“Automatic Mode.”  Press ENTER to toggle from "DISABLED" to "ENABLED."
Remember that if you set it for "Disabled,” the Automatic Single Stroke choice will not
be available in the Mode Select Menu.

2. Use the "down" cursor key to highlight the next selection, "Two Hand Only,” or press

RESET to exit.

Two Hand Only

NOTICE

This selection affects only the SmartPAC 2/WPC controls with Shadow light curtain firmware
installed. One Hand and Foot modes are not available when Shadow firmware is not installed.

1. In the Press Control Option Switch screen, Figure 4 - 33,highlight the item next to “Two

Hand Only.” Press ENTER to toggle from "Disabled" to "Enabled."

•

Enable "Two Hand Only" to make WPC a Two Hand Only control.  Enabling this
choice means that the other operating modes, One Hand and Foot, are not available.

•

Disable "Two Hand Only" to make available the other operating modes, One Hand
and Foot, if they are installed on your press.

2. Press RESET to exit.

Input Status

[INITIALIZATION – PRESS CONTROL – INPUT STATUS]

The items on this menu are useful for troubleshooting SmartPAC 2 with WPC.  See the
instructions in Chapter 7, starting on page 420.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов