manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 442 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 442

1126800 

SmartPAC 2 with WPC Integration

Page 420

Chapter 7

SmartPAC 2 Fault Messages

Using the WPC Input Status Display

[INITIALIZATION – PRESS CONTROL – INPUT STATUS]

As an aid to installation and troubleshooting, you can read the status of the inputs on the
screen of your SmartPAC.  Access this information from Initialization mode by following the
steps below.

NOTICE

The LED indicators inside the housing also show the status of these inputs.  See the figures
at the end of Chapter 4.

1. Enter the Initialization mode as described in Chapter 4.  The Main Initialization menu

appears.

2. Select “Press Control.”  The WPC Initialization menu, next figure, appears.

WPC INITIALIZATION MENU

USE THE CURSOR KEYS 

USER INTERLOCKS

TO SELECT THE ITEM  

PRESS PARAMETERS

YOU WISH TO SEE. 

 

PRESS OPTIONS

PRESS ENTER TO  

 

INPUT STATUS

ACCESS  IT. PRESS
RESET WHEN DONE.

USER INTERLOCKS

Figure 7 - 10.  WPC Initialization menu

3. Select “Input Status.”  The WPC Input Status display, Figure 7 - 11, appears.  Select the

type of input you want to see.

Press 

F2

 for “Buttons/Switches.”  See Figure 7 - 12.

Press 

F3

 for “Estops/Top Stops.”  See Figure 7 - 13.

Press 

F4

 for “Interlocks.”  See Figure 7 - 14.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов