manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 288 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 288

1126800 

SmartPAC 2 with WPC Integration

Page 266

Chapter 4

SmartPAC 2 Initialization Mode

SET CLOCK

(INITIALIZATION – DIAGNOSTICS – SET CLOCK)

F1

F2

F3

F4

F5

F6

F7

F8

Figure 4 - 45.  Clock Setting Screen

In this screen you can set the month, day, year and time.  The date is month/day/year
(mm/dd/yy).  The time is based on 24 hours, so 1:30 p.m. is 13:30 and 11:00 p.m. is 23:00

1.

 

Use the left and right cursor keys to highlight the part of the date and time that you want
to change.  Press ENTER.  A number entry box appears.

2.

 

Use the number keys or the up and down cursors to place the number you want in the
entry box.

3.

 

Press ENTER when done; press RESET to cancel and close the box.  To stop the clock,
press

 F1

.  To start it again, press 

F1

 again.

NOTICE

You will have to change the clock setting when your local time changes from Standard to
Daylight Savings time in the spring and from Daylight Savings to Standard time in the fall.

UPDATE FIRMWARE

(INITIALIZATION – DIAGNOSTICS – UPDATE FIRMWARE)

To update the firmware in your SmartPAC 2, go to “Appendix C – Update SmartPAC 2
Firmware,” page 453.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов