Honeywell SmartPAC 2 Скачать руководство пользователя страница 283 | Manualshive

Страница: 283 / 522

Honeywell SmartPAC 2 Скачать руководство пользователя страница 283

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Initialization Mode

Chapter 4

page 261

After you fill in the information on this screen, you will use SmartView to complete setting
up the e-mail messages and recipients (see “Appendix D – SmartView,” page 455) for your
SmartPAC 2.

1.

Highlight an item and press ENTER. A text-entry window appears.

2.

Fill in the appropriate name or text. Press

F6

to accept the text.

3.

Repeat for each item.

4.

When you have finished filling in the items, press

F2

to apply the changes you have

made.

NOTICE

You can use a separate computer keyboard to enter names. See page 270.

NOTICE

To e-mail a copy of this screen, see “Screen Capture,” page 199.

«
...
281
282
283
284
285
...
»

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов