Honeywell SmartPAC 2 Скачать руководство пользователя страница 131

Страница: 131 / 522

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 109

Determine the Correct Top Stop Angle

Push and hold the run buttons so the press makes a full stroke and top stops.

The display shows the crank angle at which the press stopped. Write this angle in one of
the boxes below.

Angle the Press Stopped

°
°

Repeat steps 1 and 2 at least three times; each time record the

Angle the Press Stopped

•

If the press consistently stopped after 358

and before 2

, the Top Stop Angle is

correct and does not need adjustment. Go to “Prepare to Install Magnet for Overrun
Limit Sensor,” page 116,

install the overrun limit sensor magnet.

•

If the press consistently stopped before 358

, go to the next step.

•

If the press consistently stopped after 2

, go to the next step.

•

If the press sometimes stopped before 358

and sometimes after 2

, call Wintriss

Tech Support.

From the angles you wrote in the boxes in step 2, above, find the average of the

Angles

the Press Stopped

. Write this average in the box below. You will use this value later.

Average Angle the Press Stopped

At the top of the stroke (TDC, top dead center) the crank angle is 360

or 0

At the bottom of the stroke (BDC, bottom dead center) the crank angle is 180

Look at the

Average Angle the Press Stopped

and determine whether it is

BEFORE TDC

AFTER TDC

•

BEFORE TDC

, (between 181

and 360

), go to the next section, “Determine Top

Stop Angle If Press Stopped BEFORE TDC.”

•

AFTER TDC

, (between 0

and 180

), go to “Determine Top Stop Angle if Press

Stopped AFTER TDC,” page 113.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Результаты поиска

Содержание SmartPAC 2

Отзывы:

Honeywell SmartPAC 2, Руководство пользователя, Страница: 131 / 522

Результаты поиска

Содержание SmartPAC 2

Отзывы: