manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 44 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 44

1126800 

SmartPAC 2 with WPC Integration

Page 22

Chapter 1

Introduction to SmartPAC 2

Specifications:  SmartPAC 2 with WPC

SmartPAC 2
Options,
continued

Communications

  

Connects via Ethernet to local area network and data viewed via the  Internet using
SmartView remote viewing utility
Can connect to network running PACNet Computerized Pressroom
     Reporting* software
Can be used with RSR™ remote storage and retrieval* software

SmartPAC 2
Options,
continued

Preventative Maintenance (PM) Monitor

Bilingual* (

English/Spanish) status/adjust menus

*Consult product user manual.  (i.e., DSI 2: #1121900; AutoSetPAC:  #1101600; WaveFormPAC:
#1109100; PACNet 3 Computerized Pressroom Reporting #1126200 [includes RSR] or RSR 3
Standalone:  #1126900, RamPAC:  #1115200; ProPAC: #1117500; Bilingual (English/Spanish):
#1102900).

WPC Options

Shadow V® or Shadow VI® Light Curtains

in heights from 6 to 60”; 25' or 50' scanning range; refer to Shadow literature for more
information.

WPC Options

Firmware

Muting for Shadow light curtain on the upstroke; Two-hand only; One-hand

**

, two-hand

or foot operation

**

; Automatic Single Stroke (external trip); Continuous on Demand;

Auto Compensated Top Stop (ACTS); High Speed (>500 SPM).

WPC Options

Selector Switches

One-hand, two-hand or foot operation**; Automatic Single Stroke (External Trip) to
slave the press to an external device; control switch for two operator stations; Micro-
inch on / off

WPC Options

Foot Switch

Safety switch for foot actuation** (foot operation firmware required)

WPC Options

One-hand Control

Control for one-hand actuation

**

 (one-hand operation firmware required)

WPC Options

Counterbalance Air Pressure Switch

12-150 PSI; monitors counterbalance supply (uses one customized input)

WPC Options

Bar Mode Control

Allows manual turning of crankshaft

WPC Options

Remote Crank-angle clock display

Second display can be installed up to 100' away

WPC Options

Motor Control and Custom Packages

Refer to Press/Control Motor Starter literature, and/or contact your Wintriss
representative or factory for more details.

**  Shadow light curtain required

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов