manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 46 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 46

1126800 

SmartPAC 2 with WPC Integration

Page 24

Chapter 2

Installing SmartPAC 2 and WPC

DANGER

!

ELECTRIC SHOCK OR HAZARDOUS ENERGY

•

Disconnect main power before installation.

•

Remove all power to the press, press control, and other equipment used with the press.

•

Remove all fuses and “tag out” per OSHA 1910.147 Control of Hazardous Energy (Lockout/
Tagout).

•

Ensure that Installation is performed by qualified personnel.

•

Complete all wiring installation procedures before connecting to the AC power source.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

PROGRAMMABLE CAM SWITCH NOT FOR SAFETY USE

Use SmartPAC 2’s programmable cam switch only to control auxiliary functions.  The
SmartPAC 2 programmable cam capability should never be used to provide timing signals
for any safety use, including clutch/brake control or muting of light curtains.

Failure to comply with these instructions will result in death or serious injury.

NOTICE

OPTIONAL MODULES PROCAMPAC AND DIPROPAC INCLUDED IN MANUAL

Your SmartPAC/WPC System comes standard with press control capabilities.  You may also
include one or both of the following options: DiProPAC die protection or ProCamPAC
programmable cam switch.  This manual includes instructions for installing and using these
options. Remember that they are options and might not be included in your system.

If you ordered SmartPAC with other optional modules, such as AutoSetPAC load monitor or
ProPAC process monitor, refer to the option module’s user manual for complete details on
its installation and use.

NOTICE

UPGRADING FROM ORIGINAL SMARTPAC

See “Appendix E – Upgrade from Original SmartPAC,” page 457 for instructions on
upgrading from original SmartPAC to SmartPAC 2.

This chapter describes how to install WPC, SmartPAC 2 and some SmartPAC options.

After you have completed your installation, be sure to follow the procedures under “Part 7 –
Perform Checkout Tests,” page 127, to ensure that WPC is working properly 

before

proceeding to the next chapters.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов