manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 179 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 179

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 157

User Inputs Test

To be sure the user inputs you are using are wired and operating correctly, run the test below.
Refer to “Wiring WPC User Inputs,” page 52.  If you are not using any user inputs, go to the
next section.

Run the press.  Actuate one of the user inputs.  The press should stop and the SmartPAC 2
should display the appropriate fault code.

•

If the press stops and the appropriate fault code displays, the input is wired and
operating properly.  Repeat the test for the other user inputs. When you have checked
them all, go on to the next section.

•

If the press does not stop and/or the appropriate fault code does not display, check the
wiring and rerun this test.  If the press still does not stop and/or the correct fault code
does not display, contact Wintriss Tech Support.

Cam Channels Test (Optional – with ProCamPAC)

Go into Run mode and create some test settings for your cam channels (see Chapter 6). Load
the tool, and run the press. Ensure that the equipment  (feed, blow off, lube, etc.) controlled
by each channel is working properly according to the settings you made.

Checkout Tests Complete

You have successfully checked out your SmartPAC 2 with WPC.

If your SmartPAC 2 unit is a panel mount, install it into your enclosure and tighten the
hardware.

Now you are ready to set up your system further and program tools.  Proceed to “Chapter 4 –
SmartPAC 2 with WPC Initialization Mode” and “Chapter 5 – SmartPAC 2 with WPC
Program Mode.”  Refer to Chapter 3 for instructions on how to use the SmartPAC 2 display
and keyboard.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов