manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 55 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 55

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 33

Mounting the WPC Control Enclosure

Refer to Figure 2 - 4 for mounting dimensions for the WPC control enclosure. It does not
matter where you mount the control enclosure since the displays and keypad reside at
SmartPAC 2.  However, mount the WPC it so that it will be easy to make wiring connections
and to perform maintenance, when necessary.
The control enclosure does not have to be mounted to the press. It can be mounted on a free-
standing pedestal, console, pendant, or column. For easy access to the interior, make sure that
there is enough room to open the control enclosure door at least 120°.  Plastic cable ties and
self-sticking cable clamps are provided in the accessory parts bag. Use them to position the
cable and wiring inside the control enclosure in a neat and orderly fashion.

Dimensions:  inches

        (mm)

Enclosure depth approx.

9 inches (228 mm). To fully

open the enclosure door, you

must allow clearance of approx.

25 inches (635 mm) from

mounting surface.

 17.5 REF

 (445)

16.75

(425.5)

 17.0 REF

(432)

14.00

(355.6)

 0.312 (7.92)

4 PLACES

Figure 2 - 4.  WPC Mounting Dimensions

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов