manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 270 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 270

1126800 

SmartPAC 2 with WPC Integration

Page 248

Chapter 4

SmartPAC 2 Initialization Mode

Switch 8 – Top Stop Mode for F and H Errors and Auxiliary 1 Response to
Interrupted Stroke

NOTICE

After you change switch settings, power down the SmartPAC 2/WPC. Power it up again to
enable the new settings. If you do not this, the previous switch settings will remain in effect.

Switch 8 controls two different functions:

•

Top Stop mode for F and H errors

•

How Auxiliary Output 1 responds to an Interrupted Stroke condition (see below)

See the following two sections for descriptions of how to use Switch 8 to control these
functions.

Switch 8:  Selecting Top Stop Mode for F and H Errors

You can use option switch 8 inside the unit to select whether the unit top stops the press
immediately if the error occurs after a crank angle of 210

°

.

Set Switch 8 in the Press Control Option Switches screen, Figure 4 - 33, page 241, according to
the following table.

Table 4 - 11.  Switch 8 Settings for Top Stop with F and H Errors

Option Switch 8 Setting

Top Stop Behavior for F and H Errors

OPEN

If the error occurs after 210

°

, the control allows the press to

complete another stroke before it top stops.

If the error occurs before 210

°

, the control top stops the press

on the same stroke.

CLOSED

The control top stops the press on the current stroke, even if
the error occurs after 210

°

Switch 8:  Selecting Auxiliary Output 1 Response to Interrupted Stroke

DANGER

!

NON-SAFETY OUTPUTS USED FOR SAFETY FUNCTIONS

Use auxiliary outputs 1, 2 and 3 for non-safety functions only.  They cannot protect
personnel from a moving hazard.  You can use them for convenience in automation.

Failure to comply with these instructions will result in death or serious injury.

The setting of this switch affects how Auxiliary output 1 responds to an Interrupted Stroke
condition as indicated below.  See also “Wiring Auxiliary 1 Output (Optional),” page 64.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов