manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 348 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 348

1126800 

SmartPAC 2 with WPC Integration

Page 326

Chapter 6

SmartPAC 2 Run Mode

If this happens, turn the Program/Run key to "program.” Press RESET to clear the error
message. Then load a tool number (see “LOAD NEW TOOL,” page 357). Now set the
Program/Run key to "Run.”  SmartPAC 2 will go into Run mode.

Settings Locked in Run Mode, or Password
Required

SmartPAC 2’s security access feature can lock settings in run mode, or require a password
for settings to be changed if you have the password option.  Whenever settings are locked in
Run mode, you will see a message on the screen telling you so when you select the item.  If a
password is required, enter it at the screen overlay that appears, below.

 

ENTER YOUR PASSWORD

USE THE  KEYPAD TO ENTER NUMBERS.
USE THE UP/DOWN CURSON KEYS TO
INCREASE/DECREASE. PRESS ENTER
WHEN DONE. PRESS RESET TO CANCEL.

    60599

If this display appears, you need to enter the general password to access these settings.  Password

access is set under Security Access in Initialization mode. See

 

“Security Access” in Chapter 4,

page 251.

Figure 6 - 4.  “Enter Your Password” Display

If settings are locked in Run mode, you can display the information, but nothing happens if
you try to make an adjustment.  "Adjust mode locked" means you cannot adjust settings.  If
counters are locked, you cannot change the current count.  If cam settings are locked, a
message appears on the screen that reads, "CAM ADJUSTMENT IS LOCKED OUT.
PRESS RESET WHEN DONE.”  The item "Load new tool" does not appear on the Run
menu at all if “Load New Tool” is locked in Run Mode.
For more detail, see “Security Access” in Chapter 4, page 251.

For HELP press the HELP key located at the center of the cursor (arrow) keys.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов