Chapter 11 Motion Control Instructions
11-161
11
11.4
Multi-axis Instructions
MC_GearIn
FB/FC
Explanation
Applicable model
FB
MC_GearIn is used for establishing the electronic gear relationship
between two axes.
DVP15MC11T
DVP15MC11T-06
Input Parameters
Parameter name
Function
Data type
Valid range
(Default)
Validation timing
Master
Specify the number of the
master axis which is to be
controlled by the instruction
USINT
Refer to Functions
of Section 2.2.
(The variable value
must be set)
When
Execute
changes from
FALSE to TRUE
Slave
Specify the number of the
slave axis which is to be
controlled by the instruction
USINT
Refer to Functions
of Section 2.2.
(The variable value
must be set)
When
Execute
changes from
FALSE to TRUE
Execute
The instruction is executed
when
Execute
changes from
FALSE to TRUE.
BOOL
TRUE or FALSE
(FALSE)
-
ContinuousUpdate
Reserved
-
-
-
RatioNumerator
Gear ratio Numerator
LREAL
Positive number
and negative
number
(The variable value
must be set)
When
Execute
changes from
FALSE to TRUE
RatioDenominator
Gear ratio Denominator
LREAL
Positive number
(The variable value
must be set)
When
Execute
changes from
FALSE to TRUE
MasterValueSource
Command source selection
0
:
Command position of
the master axis which
the slave axis follows
1
:
Actual position of the
master axis which the
slave axis follows
MC_Sourc
e
0:mcSetValue
1:mcActualValue
(0)
When
Execute
changes from
FALSE to TRUE
Acceleration
Specify the target
acceleration.
(Unit: Unit/s
2
)
LREAL
Positive number
(The variable value
must be set)
When
Execute
changes from
FALSE to TRUE
Deceleration
Specify the target
LREAL
Positive number
When
Execute
MC_GearIn
Mas ter
InGear
MC_G earIn_ins tanc e
Slav e
Exec ute
Busy
Act iv e
Cont inuous Upd ate
Error
E rrorID
CommandAborted
RatioNumerato r
RatioDenominator
Ac celeration
Dece leration
Jerk
Bu fferMode
Mast erValueSourc e
Содержание DVP-15MC Series
