YOKOGAWA ScopeCorder DL750 User Manual Download Page 10

Page: 10 / 406

Part 2:ix

IM 701210-06E

App

Index

13.17 Changing the Directory/File Name of the Storage Medium and Creating

Directories ............................................................................................................ 13-63

13.18 Connecting a PC to the DL750/DL750P via SCSI ............................................... 13-67

13.19 Using the Voice Comment Function ..................................................................... 13-70

Chapter 14

External Trigger I/O, External Clock Input, and Video Signal
Output

14.1

External Trigger Input (TRIG IN) ............................................................................ 14-1

14.2

Trigger Output (TRIG OUT) ................................................................................... 14-2

14.3

External Clock Input (EXT CLK IN) ........................................................................ 14-3

14.4

Video Signal Output (VIDEO OUT (SVGA)) ........................................................... 14-4

14.5

External Start/Stop Input (GO/NO-GO) .................................................................. 14-6

Chapter 15

Using the DSP Channel (Optional)

15.1

DSP Channels (Optional) ....................................................................................... 15-1

15.2

Performing Addition, Subtraction, Multiplication, and Division (DSP Channels) .... 15-3

15.3

Using Filters (DSP Channels) ................................................................................ 15-6

15.4

Performing Differentiation and Integration (DSP Channels) ................................ 15-10

15.5

Performing Addition, Subtraction, Multiplication, and Division with Coefficients (DSP

Channels) ............................................................................................................. 15-13

15.6

Using the Knocking Filter (DSP Channels) .......................................................... 15-16

Chapter 16

Ethernet Interface (Optional)

16.1

Connecting the DL750/DL750P to the Network ..................................................... 16-1

16.2

Setting up the TCP/IP ............................................................................................ 16-3

16.3

Saving/Loading Data to a Network Drive (FTP Client Function) ............................ 16-8

16.4

Setting up the Network Printer ............................................................................. 16-12

16.5

Sending Periodic Mail or Action Mail (SMTP Client Function ............................... 16-14

16.6

Accessing the DL750/DL750P from a PC or Workstation (FTP Server Function) 16-20

16.7

Using the Web Server Function ........................................................................... 16-23

16.8

Setting the Time Difference from GMT (Greenwich Mean Time)/SNTP ............... 16-48

16.9

Checking the Presence of the Ethernet Interface and the MAC Address ............ 16-50

16.10 Setting the FTP Passive Mode and LPR/SMTP Timeout ..................................... 16-51

16.11 Using the Instrument as a Windows Network Drive ............................................. 16-52

Chapter 17

Other Operations

17.1

Changing the Menu/Message Language and Turning the Click Sound ON/OFF .. 17-1

17.2

Switching the Screen Display Font Size ................................................................ 17-2

17.3

Changing the USB Keyboard Language ................................................................ 17-3

17.4

Setting the Screen Color and Brightness ............................................................... 17-4

17.5

Turning OFF the Backlight and Setting the Brightness of the Backlight ................ 17-6

17.6

Locking the Keys .................................................................................................... 17-7

Chapter 18

Troubleshooting, Maintenance, and Inspection

18.1

Troubleshooting ..................................................................................................... 18-1

18.2

Messages and Corrective Actions .......................................................................... 18-2

18.3

Self-Diagnostic Test (Self Test) ............................................................................ 18-13

18.4

Checking the System Conditions (Overview) ....................................................... 18-16

18.5

Recommended Replacement Parts ..................................................................... 18-17

Contents

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands