manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, User Manual

Share
Download
YOKOGAWA ScopeCorder DL750 User Manual Download Page 106

12-12

IM 701210-06E

• Annotation

Channel information, channel messages, or measured values are printed.  Use

Annotation to select the print interval from OFF, 200 mm, 400 mm, and 800 mm.

Use Type to select the type of annotation to be printed from CH Information, CH

Message, and CH Data.

CH Information

Prints settings such as V/div, filter, and module.

CH Message

Prints the character string (up to 80 characters) that is assigned to each channel.

CH Data

Prints the measured values at a given interval using numeric values.

The position where annotations are printed varies depending on the display

(recording) format and extra area settings as follows:

• When Format is Single, Dual, Triad, or Quad, and Extra Area is ON

The annotations are printed in the extra area.  The annotations do not overlap

the waveform print area.

• When Format is Single, Dual, Triad, or Quad, and Extra Area is OFF

The annotations are printed at the bottom section of the waveform print area.

• When Format is Octal or Hexadecimal

The annotations are printed between the divided waveform print areas (between

the grids).

Note

If all of the conditions below are met, only up to 67 characters of CH Message are printed.
Format: Single/Dual/Triad/Quad, Extra Area: OFF, Scale: Other than OFF

• Comment

A comment string of up to 20 characters can be printed at the top section of the print

area.  The comment setting is linked with the PRINT menu > Comment setting.

Preview

A preview of the print image data can be displayed in the specified output format.

Notes on Fine Print, Zoom Print, and A4 Print

• Fine print, zoom print, and A4 print cannot be carried out while waveform acquisition

is in progress.

• Only Main waveforms are applicable for fine print and A4 print.

• If waveforms are being displayed using the history memory function, only the

waveforms specified by Selected Record No. are applicable for fine print, zoom print,

and A4 print.

• Fine print, zoom print, and A4 print cannot be carried out when X-Y waveforms are

being displayed.

• Fine print, zoom print, and A4 print cannot be carried out on waveforms acquired

using the snapshot, accumulated waveform, and dual capture functions.

• If the number of printed pages exceeds 100, fine print cannot be carried out.  (The

number of printed pages is determined by the Print Mag and Time Range settings.)

12.2  Printing on the Built-in Printer

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands