manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, User Manual

Share
Download
YOKOGAWA ScopeCorder DL750 User Manual Download Page 388

App-56

IM 701210-06E

Shunt Calibration Procedure

1. Calculate the strain value (

µ

STR) corresponding to the shunt resistor to be used.  For

the calculation procedure, see “Calculating the Shunt Resistance” in the next section.

2. Execute balancing without applying a load to the strain gauge and correct the zero point.

3. Execute shunt calibration and correct the gain.

Shunt calibration is executed using DL750/DL750P channel menu > Linear Scale >

Mode.  Usually, the negative gain is corrected.  However, if you are correcting the

positive gain, change the position of the shunt resistor as shown in the upper right

figure.

Strain input

Strain

The zero point is 
corrected when 
balancing is executed.

Strain

P2:Y

P2:X

Strain input

• Balance

• Shunt calibration

The strain value corresponding to the 
shunt resistor is set to P2:Y of the setup menu.

Current measured 
value

Before 
execution

After 
execution

Before execution

After execution
Gain is corrected.

1. Automatically obtained when shunt calibration is executed.

1

Execution Menu of Shunt Calibration

The execution menu of shunt calibration is set using channel menu > Linear Scale >

Mode.  In normal shunt calibration, only P2:Y is set.  In addition to the normal shunt

calibration (when the shunt calibration relay circuit is ON), the DL750/DL750P allows the

setting of a zero point when the relay circuit is OFF.  This function is useful when the

strain value is not 0 after the execution of balancing.

Items in the Execution Menu

(1)P1:X:

If (Shunt Cal) Exec is executed, the input value when the relay circuit is OFF

is applied.

(2)P1:Y:

Sets the value (usually 0) when the relay circuit is OFF.

(3)P2:X:

If (Shunt Cal) Exec is executed when the relay circuit is ON, the input value

when the relay circuit is ON is applied.

(4)P2:Y:

Set the strain value corresponding to the shunt resistance when the relay

circuit is ON.

(1)

(2)
(3)
(4)

Appendix 11 Shunt Calibration of the Strain Module

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands