manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, User Manual

Share
Download
YOKOGAWA ScopeCorder DL750 User Manual Download Page 119

13-6

IM 701210-06E

13.2 Internal Hard Disk (Optional)

CAUTION

• When using the DL750/DL750P in a vibrating environment, turn OFF the motor

rotation of the internal hard disk.

• Do not place more than 512 files in the root directory of the internal hard disk.  If

the number of files exceeds 512, all file access operations slows down.  In

addition, the operation of realtime recording cannot be guaranteed.

• If an external SCSI device is connected, do not change the HDD Motor setting.

Procedure

FILE

SHIFT

HELP

MISC

NUM  KEY

PROTECT

VOICE
MEMO

IMAGE

SAVE

PRINT

SNAPSHOT CLEAR  TRACE

MENU

MENU

1.

Press 

MISC

.

2.

Press the 

Next 1/2 

soft key.

3.

Press the 

Others

 soft key.

4.

Press the 

HDD Motor

 soft key to select ON or OFF.

Explanation

You can turn ON/OFF the motor rotation of the internal hard disk on the DL750/DL750P.

If you turn OFF the internal hard disk motor, the internal hard disk cannot be accessed.

To save various data to the internal hard disk, turn the HDD Motor ON.

Turning OFF the HDD Motor protects the internal hard disk from vibrations.

Note

Even if the motor rotation is turned OFF, the motor rotation is turned ON for approximately 1
minute after the power is turned ON.

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands