YOKOGAWA ScopeCorder DL750 User Manual Download Page 50

Page: 50 / 406

11-12

IM 701210-06E

Changing the Magnification and Display Position

11.

As with the zoomed waveform, you can change the zoom rate of Z1 and Z2 by

pressing the

Z1 Mag/Z2 Mag

soft key and turning the

jog shuttle

12.

As with the zoomed waveform, you can move the section that is being zoomed

on Z1 or Z2 window by pressing the

Z1 Position/Z2 Position

soft key and

turning the

jog shuttle

Setting the Display Position of the Search Results

(When Mode in the ZOOM Menu Is Set to Z1&Z2 or Main&Z1&Z2)

13.

Press the

Result Window

soft key to select Z1 or Z2.

Executing the Search

14.

Pressing the

Exec

soft key to execute the search. The Exec soft key changes

to Abort. To abort the search, press the

Abort

soft key.

The search results are displayed in the zoomed waveform display position

selected in step 11. You can search 1000 times using the same conditions.

While search is in execution,

is displayed at the upper left corner of the

screen.

Displaying the Previous Search Results

15.

Press the

Searched Pattern

soft key.

16.

Turn the

jog shuttle

to specify the number of the search result you wish to

display. Newer search results are displayed with higher numbers (result 2 is

newer than result 1).

11.4 Search Data Using Search and Zoom Function

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands