manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, User Manual

Share
Download
YOKOGAWA ScopeCorder DL750 User Manual Download Page 54

11-16

IM 701210-06E

Notes When Searching

• Searching is not possible while the data acquisition is in progress.

• The search result is void if the following operations are carried out:

• When data acquisition is started.

• When Search Setup is changed.

• Patterns of waveforms that are not displayed are not searched.

• If the waveform is inverted or the offset voltage is changed, the search is performed

on the waveform after the change.

Determination When Using the Edge for the Search

When the peak immediately after the rising edge of the waveform is less than or equal to

the upper limit of the hysteresis or when the peak immediately after the falling edge is

greater than or equal to the lower limit of the hysteresis, it is determined as false (not

counted as a specified edge).

Specified level

Search start position

Detection position

Upper limit of 

hysteresis

This rising edge is determined to be false.

When the edge is set to rising and the count is set to 2

Lower limit of 

hysteresis

In addition, in the determination of logic waveforms, the determination is performed two

points after the detected position.

Search start position

When the edge is set to rising

Detection position

Detection position

Search restart position
(Not detected here)

Detection position

Auto Scroll

Set the scroll speed using 10 levels from 1 to 10.  The speed increases as the number

gets larger.  You can only change the Direction and Speed while auto scroll is in

progress.

Playing of the Voice Memo (Voice Search)

When using the voice search function, the voice memo that has been found can be

played by pressing the Play Start soft key.  The voice memo can be played only when

the searched item is the newest waveform that has been acquired to the acquisition

memory.  While the voice memo is being played, Play Start indication changes to Play

Stop.  To stop the voice memo while it is playing, press the Play Stop soft key.  When

the voice memo is finished playing Play Stop automatically changes to Play Start even if

the Play Stop soft key is not pressed.

Note

Waveform acquisition cannot be started when the SEARCH menu is displayed.

11.4 Search Data Using Search and Zoom Function

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands