YOKOGAWA ScopeCorder DL750 User Manual Download Page 163

Page: 163 / 406

13-50

IM 701210-06E

Executing the PDF File Generation

34.

Press

PRINT

. A PDF file is created using the conditions set in steps 4 to 33.

Pressing

PRINT

again aborts the save operation. While the data is being

saved, an icon corresponding the save destination medium (

FD,

Zip disk,

PC card,

external SCSI device,

internal HD, or

USB storage

device) is displayed in the upper left corner of the screen.

Explanation

Print to

When creating a PDF file of the print image (image similar to the printed output of fine

print), set the print destination to PDF.

Selecting the Section to Be Output to the PDF File: Time Range1/Time Range2

Can be specified only when displaying T-Y waveforms. Set the output start point and

output end point of the section to be output to the PDF file.

Print Magnification: Print Mag

Can be specified only when displaying T-Y waveforms. Set the waveform magnification

for creating the PDF file. The top section of the menu shows the magnification; the

bottom section shows the number of pages when the PDF file is created using the

magnification indicated in the top section.

Print Setup

Format, Extra Area, Flexible Zone, and Graticule (Scale)

The items other than graticule can be specified only when displaying T-Y waveforms.

The format, extra area, flexible zone, and graticule (scale) settings are the same as

the settings when performing fine print or zoom print on the built-in printer. For

details, see page 12-10.

Details

• Time Print/Gauge Print

Can be specified only when displaying T-Y waveforms. The time print and gauge

print settings are the same as the settings when performing fine print or zoom print

on the built-in printer. For details, see page 12-11.

The scale value and channel label are not printed when creating a PDF file.

• Annotation

Can be specified only when displaying T-Y waveforms. The annotation setting is

the same as the setting when performing fine print or zoom print on the built-in

printer. For details, see page 12-11. When creating a PDF file, annotations are

not printed if the print interval is set to OFF. However, if the print interval is set to

value other than OFF, annotations are printed on each page of the PDF file.

• Scale

Can be specified only when displaying X-Y waveforms. Select whether to print the

scale.

• Comment

The comment setting is the same as the setting when performing fine print or zoom

print on the built-in printer. For details, see page 12-11.

13.13 Creating PDF files of the printed image (DL750P only)

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands