manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, User Manual

Share
Download
YOKOGAWA ScopeCorder DL750 User Manual Download Page 318

19-30

IM 701210-06E

19.12 Module Specifications

Item

Specifications

Reference junction compensation accuracy (when the input terminal temperature is balanced)

K, E, J, T, L, U, and N:

±

1

°

C

R, S, B, and W:

±

1.5

°

C

Au7Fe:

±

1 K

Bandwidth limit (digital filter)

Select from OFF, 30 Hz, 8 Hz, and 2 Hz

Input bias current

20 nA or less
The zero point appears to be offset when the input is open due to the effects of bias current on this
module.  However, this is not a malfunction.
Connect the input to the object to be measured.

1.

Value measured under standard operating conditions (section 19.11).

2.

Does not include the reference junction temperature compensation accuracy.

3.

This module supports Au7Fe with 0.07% metal content with respect to gold.

H

L

5.

4.

6.

The typical value is a representative or standard value.  It is not strictly warranted.

WARNING

• Do not apply input voltage exceeding the maximum input voltage or allowable

common mode input voltage.

• To prevent the possibility of electric shock, be sure to furnish protective earth

grounding of the DL750/DL750P.

• To prevent the possibility of electric shock, be sure to fasten the module screws.

Otherwise, the electrical and mechanical protection functions will not be

activated.

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands