YOKOGAWA ScopeCorder DL750 User Manual Download Page 134

Page: 134 / 406

13-21

IM 701210-06E

Saving and Loading Data

Loading the Waveform Data

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Press

FILE

Press the

File Item

soft key. The File Item setup menu appears.

Press the

Waveform

soft key.

Selecting the Data Type

Press the

Data Type

soft key. The data type selection menu appears.

Press the

Binary

soft key.

Selecting the Load Source Medium/Directory

Press the

Load

soft key. The load setup menu and File List window appear.

Select the load source directory according to steps 13 to 18 in “Saving the

Waveform Data.”

Selecting the File to Be Loaded

Turn the

jog shuttle

to select the file.

Executing the Load Operation

Press the

Load Exec

soft key. A dialog box appears showing the module

information of the selected waveform data and the current module information of

the DL750/DL750P.

10.

Press the

Load Exec

soft key again. The selected file is read from the directory

indicated in Path=...... At the same time, the

Load Exec

soft key changes to an

Abort

soft key.

Note

•

Waveform data on modules whose information differs from the current module information
of the DL750/DL750P cannot be loaded.

•

Waveform data that has voice memo recorded (waveform data in binary format (.wvf
extension) and realtime recorded waveform data (.wdf extension)) can also be loaded.
For details on the voice memo function, see section 7.9.

Aborting the Load Operation

11.

Press the

Abort

soft key. The load operation is aborted. At the same time, the

Abort

soft key changes to a

Load Exec

soft key.

Specifying the Files to Be Displayed in the File List Window and Displaying Properties

12.

Carry out steps 27 to 29 in “Saving the Waveform Data.”

Note

When a file saved by specifying Z1 (or Z2) is loaded, the data of the record length of Z1 (or
Z2) is displayed right justified.

13.7 Saving/Loading the Waveform Data

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands