YOKOGAWA ScopeCorder DL750 User Manual Download Page 323

Page: 323 / 406

19-35

IM 701210-06E

Specifications

Acceleration/Voltage Module (with AAF) (701275) Specifications

Item

Specifications

Standard operating

Temperature: 23

conditions

Humidity: 55%

10% RH

After a 30-minute warm-up and after calibration

Effective measurement

20 div (display range: 10 div)

range

Number of input channels

Input coupling settings

AC, DC, ACCL (acceleration), and GND

Maximum sample rate

100 kS/s

Input format

Isolated unbalanced

Frequency characteristics

(–3 dB point when a sine wave of amplitude

3 divisions is input)

Waveform measurement mode:

DC to 40 kHz

Acceleration measurement mode:

0.4 Hz to 40 kHz

Voltage-axis sensitivity

When using 1:1 probe attenuation:

5 mV/div to 10 V/div (1-2-5 steps)

setting

When using 10:1 probe attenuation:

50 mV/div to 100 V/div (1-2-5 steps)

(combined with the recommended probe 701940)
Acceleration (

5 V =

1 range):

0.1 to

1 to

100 (in 1-2-5 steps)

Maximum input voltage (at a frequency of 1 kHz or less)

42 V (DC+Acpeak)

Maximum allowable common mode voltage (at a frequency of 1 kHz or less)

Working voltage of safety standard
30 Vrms (CAT I and CAT II)

DC offset Maximum selectable range

5 div

Vertical (voltage) axis

Waveform measurement mode

DC accuracy:

(0.25% of 10 div)

accuracy

Acceleration measurement mode:

(0.5% of 10 div) at 1 kHz

Input connector

Metal BNC connector

Input impedance –3dB

1 M

Ω ±

1%, approx. 35 pF

point when AC coupled Low0.4 Hz or less (0.04 Hz or less when using the 701940) (typical

)

frequency attenuation point

Common mode rejection ratio
80 dB (50/60 Hz) or more (typical

)

Residual noise level

100

V or

0.01 div, whichever is greater (typical

)

(Input section shorted)

A/D conversion resolution

16 bits (2400 LSB/div)

Temperature coefficient

When in waveform measurement mode (excluding AUTO filter)

Zero point:

(0.02% of 10 div)/

C (typical

)

Gain:

(0.02% of 10 div)/

C (typical

)

Bandwidth limit

Select from OFF, Auto, 4 KHz, 400 Hz, and 40 Hz

Cutoff characteristics:

–12 dB/OCT (typical

, excluding AUTO)

Cutoff frequency (fc) when set to AUTO

Sample rate of 100 kHz or higher:

fc = 40 kHz

Sample rate of 100 Hz to 50 kHz:

fc = 40% of the sampling rate

Sample rate of 50 Hz or less:

fc = 20 Hz

Cutoff characteristics when set to AUTO:

–65 at 2

fc (typical

)

Probe attenuation setting

Voltage probe

1:1, 10:1, 100:1, or 1000:1

Current probe

10 A:1 V (for the 700937/701933), 100 A:1 V (for the 701930/701931)

Compatible probes/cables Connection cable (for low voltage 1:1)

366926 (non-isolated type BNC-alligator clip

2: For measuring low voltage less than or equal to

42 Vpeak)

Voltage probe (10:1 passive probe) 701940

17 to 46 pF: For measuring 600 V (DC+ACpeak) or less

Current probe (power can be supplied from the DL750/DL750P)

700937 (15 A), 701930 (150 A), 701931 (500 A), 701933 (30 A)

Sensor supply current

OFF or 4 mA

10% (approx. 22 VDC)

(voltage)

Applicable acceleration

Built-in amplifier type

sensor

Kistler Instrument Corporation: Piezotron, PCB Piezotronics Incorporated: ICP, ENDEVCO
Corporation: ISOTRON, etc.

19.12 Module Specifications

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands