YOKOGAWA ScopeCorder DL750 User Manual Download Page 184

Page: 184 / 406

13-71

IM 701210-06E

Saving and Loading Data

Note

An icon

appears at the upper left corner of the screen while voice comment recording is in

progress.

Playing a Voice Comment (Confirmation before Saving the Data)

Press the

Play

button. The voice comment recorded in step 2 and 3 is played.

Note

•

If the recorded voice comment is not needed, the voice comment can be erased using the
Erase button.

•

An icon

appears at the upper left corner of the screen while voice comment is being played.

Used only when erasing
a recorded voice comment.

Executing the Screen Image Data Save Operation

Press

IMAGE SAVE

. The voice comment data is saved along with the screen

image data to the storage medium.

Note

The procedure and explanation for saving the screen image data are the same as those in
section 13.11. For details, see section 13.11.

Playing of the Voice Comment

The saved voice comment can be played from the File List window of the IMAGE and

FILE menus.

Open the File List window according to steps 1 to 4 on page 13-42 or steps 1 to

6 on page 13-44.

Turn the

jog shuttle

to select the screen image data file in the File List window.

Press

SELECT

. The voice comment is played at the same time the thumbnail

of the selected screen image data file is displayed at the lower right section of

the File List window.

To clear the thumbnail, turn the

jog shuttle

Thumbnail screen

Note

•

While voice comment is being played,

is indicated at the upper left corner of the

screen.

•

The procedure of opening the File List window from the Image Save or File menu is the
same as that in section 13.12. For details, see section 13.12.

13.19 Using the Voice Comment Function

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands