YOKOGAWA ScopeCorder DL750 User Manual Download Page 113

Page: 113 / 406

12-19

IM 701210-06E

Printing the Screen Image Data

Executing the Print Operation

12.

Press

PRINT

. The screen image data is printed on the network printer. To

abort printing, press

PRINT

while printing is in progress.

While printing is in progress,

is indicated at the upper left corner of the

screen.

Explanation

Like the built-in printer, you can print the screen image data on a network printer

via the

Ethernet network.

1. Printing is possible on a printer or printer server supporting the TCP/IP protocol.

Selecting the Output Format

The following six printer formats are supported.

• ESC-P

• ESC-P2

• LIPS3

• PCL5

• BJ

• PostScript

Output Resolution When Printing Using the BJ Format

When printing the screen image data to a BJ printer, select the output resolution from

180 dpi, 300 dpi, 360 dpi, and 600 dpi.

Comment

A comment string of up to 20 characters can be printed at the bottom right section. The

comment setting is linked with the PRINT menu > Comment setting.

Color

Select from the following:

ON:

Print the data using colors similar to the screen. (No background color and grid

printed in black)

OFF: Prints the image using the same colors as the image printed using the built-in

printer.

Note

Printing is possible on printers that support the TCP/IP protocol.

12.4 Printing the Screen Image Data on a Network Printer

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands