YOKOGAWA ScopeCorder DL750 User Manual Download Page 173

Page: 173 / 406

13-60

IM 701210-06E

13.16 Copying Files

CAUTION

Never remove the storage medium (disk) or turn OFF the power while the

access indicator or the floppy disk, Zip disk, internal hard disk (optional), or USB

storage device icon is blinking. Such acts can damage the storage medium or

destroy the data on the medium.

Procedure

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Press

FILE

Press the

Utility

soft key. The Utility setup menu and the File List window

appear.

Press the

Function

soft key. The file function selection menu is displayed.

Press the

Copy

soft key.

Selecting Media and Directories

Select the medium and directory according to steps 4 to 9 in section 13.8,

“Saving/Loading the Setup Data.”

Selecting the Copy Source Files One at a Time

Turn the

jog shuttle

to select the file.

Press the

Set/Reset

soft key. An asterisk (*) to the left of the selected file to

indicate that it will be copied. Pressing the

Set/Reset

soft key again removes

the asterisk (*) to the left of the selected file. The file will not be copied.

Proceed to step 11.

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands