YOKOGAWA ScopeCorder DL750 User Manual Download Page 146

Page: 146 / 406

13-33

IM 701210-06E

Saving and Loading Data

Loading Snapshot Waveforms

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Press

FILE

Press the

File Item

soft key. The File Item setup menu appears.

Press the

Snap

soft key.

Selecting the Load Source Medium/Directory

Press the

Load

soft key. The load setup menu and File List window appear.

Select the load source directory according to steps 4 to 9 in “Saving Snapshot

Waveforms.”

Selecting the File to Be Loaded

Turn the

jog shuttle

to select the file.

Executing the Load Operation

Press the

Load Exec

soft key. The selected file is read from the directory

indicated in Path=...... At the same time, the

Load Exec

soft key changes to an

Abort

soft key.

Aborting the Load Operation

Press the

Abort

soft key. The load operation is aborted. At the same time, the

Abort

soft key changes to a

Load Exec

soft key.

Specifying the Files to Be Displayed in the File List Window and Displaying Properties

Carry out steps 19 to 21 in “Saving Snapshot Waveforms.”

13.9 Saving/Loading Snapshot Waveforms

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands