YOKOGAWA ScopeCorder DL750 User Manual Download Page 273

Page: 273 / 406

18-2

IM 701210-06E

18.2 Messages and Corrective Actions

Error Message

A message may appear during operation. This section describes the meanings of the

messages and their corrective actions. The messages can be displayed either in English

or Japanese (see section 17.1). If the corrective action requires servicing, contact your

nearest YOKOGAWA dealer for repairs.

In addition to the error messages below, there are communication error messages.

These messages are described in the

Communication Interface User’s Manual IM

701210-18E

(separate manual).

Status Messages

Code

Message and Corrective Action

Section

File access is aborted.

Chapter 13

Exit from GO/NO-GO mode.

11.8, 11.9

Image printing was aborted.

Chapter 12

Cannot set all about zone.

11.9

Write to the EEPROM complete. Wrote module-specific information to the module.

–

Calibrating the temperature module.

–

Temperature module calibration complete.

–

The instrument is set to remote mode by the communication control.

–

Press the SHIFT + CLEAR TRACE key to change to local mode.

Terminating...

–

Turned on pressing the RESET key. Will initialize.

4.4

A strain module is installed. Carry out automatic balancing before use.

–

The setting of the excitation voltage or the gauge factor was changed.

–

Carry out automatic balancing before use.

Automatic balancing is running...

–

Automatic balancing is complete.

–

Test: SUCCESS

–

Calibration is running...

4.6

Calibration is complete.

4.6

Completed action-on-trigger.

6.17

Release the Preview mode.

12.2

Aborted the search.

11.2 to 11.4

Executed the search, but no record was found that matched the conditions.

11.2

Executed the search, but no record was found that matched the pattern.

11.4

Pattern contains points that are between Thr Lower and Thr Upper.

11.4

Aborted the statistical measurement.

–

This model does not have the DSP option installed.

–

Averaging is in progress.

11.1

Averaging has been completed.

11.1

Input module configuration was changed. Relevant settings have been initialized.

–

Parameter block has been set. Restart to update the instrument configuration information.

–

There is no dry cell. Insert batteries or turn the backup switch OFF.

7.10

All operation was aborted due to a power disruption. The data before the disruption is stored.

7.10

No data was acquired during the disruption.

When history is set to “All,” data of math channels is not saved.

11.1

To store the data of math channels, set history to “One.”
* Data of channels other than math is saved.

This model does not have computation option installed.

–

This model does not have the HDD option installed.

–

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL750, User Manual

Search results

Summary of Contents for ScopeCorder DL750

Reviews:

Brands by name

Popular brands